Glazed Ginger Bars Recipes

GINGERBREAD BARS

Steps:

• Preheat oven to 350°F/175°C. Line a 9×9-inch pan with parchment paper, leaving enough overhang on the sides for lifting the bars out of the pan after baking.
• In a medium bowl, sift together flour, ginger, cinnamon, nutmeg, baking soda, and salt. Set aside.
• In a mixer bowl fitted with the paddle attachment, beat butter and sugar on medium speed for 3-4 minutes, until fluffy. Add molasses, egg, and vanilla, and beat until combined. Add flour mixture and mix just until combined.
• Spread dough evenly into prepared pan and smooth the top. Bake for 18-22 minutes, until the top is slightly firm to touch, and a toothpick inserted into centre comes out with a few moist crumbs, not clean. Overbaking will make the bars dry. Allow to cool completely in pan.
• To make the glaze: In a small bowl, combine powdered sugar, 1 tablespoon milk, and vanilla extract, and whisk until smooth. Add more milk as necessary until you get a thick yet pourable consistency. Drizzle over the bars using a spoon or a piping bag. Allow glaze to set, 15-30 minutes. For easy cutting, you can place it in the fridge for 2 hours until firm. Lift out of the pan and cut into squares. Serve at room temperature.
• Store bars in an airtight container at room temperature for up to 3 days, or freeze for up to 2 months.

TARTINE'S SOFT GLAZED GINGERBREAD

Steps:

• To make the dough, stir together the flour, cocoa powder, ginger, cloves, cinnamon, baking soda, salt, and pepper in a mixing bowl. Set aside.
• Using a stand mixer fitted with the paddle attachment, beat the butter on medium-high speed until creamy. Slowly add the granulated sugar and mix on medium speed until the mixture is completely smooth and soft. Stop the mixer and scrape down the sides of the bowl with a rubber spatula as needed.
• Add the egg and mix well. Add the molasses and corn syrup and beat until incorporated. Stop the mixer again and scrape down the sides of the bowl.
• Add the flour mixture and beat on low speed until a dough forms that pulls away from the sides of the bowl and all the ingredients are well incorporated.
• Remove the dough from the bowl, flatten it on a large piece of plastic wrap into a rectangle about 1 inch thick, cover the dough with the plastic wrap, and refrigerate overnight.
• Preheat the oven to 350 degrees. Line a baking sheet with parchment paper or a nonstick liner.
• Unwrap the dough and place on a floured work surface. If using a plaque with a design, roll out the dough 1/3 inch thick, lightly dust the top with flour, press your cookie molds over the dough, and then cut out the shapes with a small knife and place on the prepared baking sheet, spacing them about 1 inch apart. Alternatively, using the mold as a guide, cut around it with a small knife, flip the mold over so the design is facing you, and place the dough over it, pressing it into the design. Unmold the shapes onto the prepared baking sheet, leaving about 1 inch between them.
• If using a patterned rolling pin, lightly dust the lined baking sheet with flour and transfer the dough to the pan. Lightly dust the top of the dough with flour and roll it into a rectangle about 1/3 inch thick with a plain pin. Then, using the patterned pin, roll over the dough with enough pressure to ensure a clear impression of the design. Trim the sides with a small knife. It is not necessary to cut into smaller sizes before baking.
• Bake the cookies until lightly golden along the sides but still soft to the touch in the centers, 7 to 15 minutes. The timing will depending on the size of the individual cookies, or if you have made a single large patterned piece that will be cut after baking.
• While the cookies are baking, prepare the glaze. In a small bowl, whisk together the confectioners sugar and water until smooth.
• When the cookies are ready, remove from the oven and let cool on the pan on a wire rack for about 10 minutes. Then, while the cookies are still warm, using even strokes, brush a light coat of glaze on the top of each cookie, evenly covering it.
• Let the cookies cool completely. When the glaze dries, it should leave a shiny, opaque finish. If you have used a patterned pin to make a single large plaque, cut into the desired sizes with a small, very sharp knife. At the bakery, we cut them into 3-by-4-inch rectangles, but 1 1/2 by 4 inches makes a nice smaller size.